
Commercial Metal Roof Repair
Screws, laps, ridge caps, and rusted panels on shops and storage buildings.
Metal roof repair
As a Shelton commercial roof repair contractor, we fix leaking screws, open laps, and rusted panels on metal shops, storage buildings, and equipment sheds.

Shelton commercial roof repair often means metal roofs on shops, machine sheds, and storage buildings. Leaks on these roofs usually start at fasteners, laps, and flashing, while the panels themselves often have plenty of service left.
We replace worn screws, reseal laps, and swap individual rusted panels, and tell you plainly when rust has spread far enough that replacement makes more sense. Condensation gets checked too, since it can look like a leak on cold mornings.
Metal buildings leak in the same few places. These are the problems Shelton owners call about most.
One row of screws has lost the seal at its washers, usually along a purlin where the roof flexes most.
We replace every screw on that run with an oversized fastener and a new washer.
Water and debris sit at the lower panel ends, keeping the steel wet until it rusts through.
Rusted panel ends are replaced with matching panels, and the eave closure is renewed.
Ridge cap screws and foam closures loosen, and wind drives rain up under the cap.
Caps are refastened or replaced with new closures and sealant at every lap.
Warm, moist air inside a cold metal building condenses on the panels and drips in winter.
We check the laps and screws for real leaks first, then point out where insulation or venting is the issue.
A leaking metal roof wets whatever sits under it. Here is what each repair keeps dry.
Drips onto machinery, tools, and stored feed cause rust and spoilage.
New screws and sealed laps keep the floor below dry.
Leaking screw holes rust outward and turn a fastener problem into a panel replacement.
Early fastener work keeps the panels in service.
Wet faced insulation sags, drips, and holds moisture against the steel.
Stopped leaks let the insulation dry out instead of being replaced.
Long-running leaks rust the purlins and fasteners that hold the whole roof.
Repairs made early keep the framing off the repair list.
Metal roof repair leads in Shelton, and the other three services cover the rest of the property.

Screws, laps, ridge caps, and rusted panels on shops and storage buildings.
Metal roof repair

Leaks that run along purlins before dripping, traced back to the right lap.
Roof leak repair
Processing and grain buildings with fans, vents, and equipment on the roof.
Industrial roof repairCall us with what the roof is made of and where water lands inside. That lets us bring matching screws and panels the first time.
Metal roof visits follow the fastener rows and laps from one end of the building to the other.
We match drip points inside to fastener rows and laps above, checking the eaves and ridge on the way.
Oversized screws with new washers go in along every leaking run, and empty holes get sealed patches.
Laps are resealed with butyl tape, and rusted-through panels are swapped for matching profiles.
Before we leave, you hear which panels to watch and whether condensation needs its own fix.
Our repair work reaches Shelton and the towns below. Not on the list? Call us or send us a message.

Flat, metal, leak, and industrial roof repairs across Kearney.
Shared walls and tight lots planned into every repair.
Edges, flashing, and seams checked after hail and wind.
Repairs scheduled around weather and business hours.
Leak logs used to find entry points sooner.
Answers for Shelton owners on metal roofs, cost, and finding a contractor nearby.
Often, yes. When the panels are still solid and leaks come from screws, laps, and flashing, we replace worn screws, reseal the laps, and swap individual rusted panels. Replacement becomes the better choice when rust has spread through many panels or the framing is damaged. An inspection shows which one fits your building.
The number of screws, laps, and panels that need work sets most of the cost. Replacing panels costs more than resealing because of profile matching and removal. Eave height, building width, and lift access add time, and insulation soaked by old leaks can add to the scope.
Yes. We repair commercial roofs in Shelton and in Kearney, Holdrege, Minden, Gibbon, and Ravenna. Call with the address, the panel type, and where the drips show, and we will set up an inspection.
We cover farm and storage buildings around Shelton. Machine sheds and grain or feed storage get the same fastener, lap, and panel repairs as commercial shops, scheduled around harvest and feeding times where needed.
Leaks follow rain or snowmelt and line up with screws or laps. Condensation shows on cold mornings with no rain at all, dripping across many spots at once. We check the screws and laps first, then tell you if insulation or venting is behind the drips.
Tell us the building size, the panel type, and where water lands. We will inspect the roof and price the repair in writing.